Touch 'N' Seal Spray Foam Kits - Technical Data :
Rigitech ® is a distributer for 'Touch 'N' Seal' 2-Component Foam. Touch 'N' Seal is designed for use by the professional in commercial air sealing, insulating, patching and filling voids. The high closed cell content of the cured foam makes the 2-Component Foam System suitable as a general sealant to prevent air leakage in all insulating and sealing applications.
Features of Touch 'N' Seal 2-Component Foam include:
- Portable/disposable, self-contained units,
- Upright hose assembly, easy set-up and application,
- A full hose reach up to 30M for reduced lifting,
- Ease of control - meter from low to high output,
- Less waste - can be stored up to 90 days and restarted,
- Expansion to 30 times, and curing time within 45 seconds,
- Clear, color-coded hoses,
- Lock "ON" for less operator fatigue, lock "OFF" for safety.
Product Technical Statistics:
| Density ASTM D-1622 | 1.75 ± 0.2 pcf |
| K-Factor ASTM C-177 | 0.144 |
| R-Factor ASTM C-177 | 6.9/in |
| Compressive Strength ASTM D-1621 | 10%, parallel: 19 psi
10%, perpendicular: 13.4 psi |
| Dimensional Stability ASTM D-2126 | -40°F, 2-wks: +.88% vol. change 158°F;
100% RH 2-wks: +14% vol. change |
| Water Absorption ASTM D-2842 | 1-3.5% |
| Closed Cell Content ASTM D-2856 | 90%,min |
| Shelf Life | 18 months |
Touch 'N' Seal Spray Foam Kit Installation:
Read all instructions and safety information (MSDS) prior to use of any product.
- Application: For optimum performance and foam quality, the temperature of the spray environment and foam materials should be 21.2-26.6°C (70-80°F). Application in temperatures below 21.2°C (70°F) may increase set up time and reduce overall performance of all polyurethane foam. Use only in well ventilated area.
- Storage: Materials may be stored below 21.2°C (70°F), however, temperatures of A & B canister materials must be brought to a minimum of 21.2°C (70°F) prior to application. Canisters stored in low temperatures may require more than 24 hours to warm their chemical contents.
- Limitations: This product is not a fire stop or fire barrier penetration sealant!
PRODUCT SAFETY - NECESSARY!
- CAUTION: Heat/Combustionable releases.
- This product is NOT A FIRE STOP OR FIRE BARRIER penetration sealant.
- Foam bonds to skin quickly - WEAR PROTECTIVE GEAR, gloves and safety glasses during application.
- HAZARDOUS DECOMPOSITION PRODUCTS.
- Contains MDI Monomer and Chlorodifluoromethane. Do not puncture or incinerate tanks. Do not expose to heat or store at temperatures above 120°F (49°C). Do not store in vehicles or warehouses where temperatures may exceed 120°F (49°C). Do not expose to heat, sparks, or open flames. This product is not intended for use in applications where temperatures exceed 250°F (121°C).
FIRST AID
- In case of eye contact, flush eye with water for 15 minutes and get immediate medical attention.
- If ingested, call a physician.
- Remove wet foam immediately from skin with acetone or nail polish remover. Dried foam is hard to remove from skin.
- If foam dries on skin, apply generous amounts of petroleum jelly or lanolin, leave on for one hour, wash thoroughly, and,repeat process until foam is removed. Do not attempt to remove dried foam with solvents.
- KEEP OUT OF REACH OF CHILDREN – NOT FOR USE BY CHILDREN.
